Electrolux dishwasher — Error Code i10
The appliance is failing to intake water or cannot register that it has filled.
What it means
The i10 fault on an Electrolux dishwasher signifies a fill timeout. When a cycle initiates, the main control board delivers 120V AC to the water inlet valve solenoid to trigger water flow. Simultaneously, the system tracks the analog pressure sensor (or pressure switch) to confirm the tub is accumulating water. If the pressure sensor fails to detect the required water level within the set window (usually 90 to 120 seconds), the control board stops the process, runs the drain pump as a safety precaution, and displays the i10 alert. This issue generally stems from a failure in the water supply path, a blockage in the pressure sensor's air trap, or an electrical malfunction preventing the inlet valve from engaging.
Likely Causes
- 1 Restricted Water Supply or Low PressureThe shut-off valve beneath your sink might be closed, or your home's water pressure is below the 20 psi threshold needed to actuate the inlet valve diaphragm.
- 2 Obstructed Water Inlet Valve ScreenMineral buildup from hard water—common in areas like Spokane—or sediment can clog the fine mesh filter located inside the water inlet valve at the supply line connection.
- 3 Defective Water Inlet ValveThe solenoid coil inside the inlet valve might experience an open circuit or mechanical seizure, preventing water entry even when the control board provides the necessary 120V.
- 4 Malfunctioning Pressure Sensor or Blocked Air TrapThe pressure sensor relies on an air column to track levels. If the air trap becomes fouled with grease or the sensor itself fails, the board stays unaware that the unit is filling.
- 5 Control Board or Wiring IssuesA damaged wire harness or a failed relay on the main electronic control board can interrupt the voltage path to the inlet valve.
How to clear / reset
To reset the i10 error, hold the Start/Cancel button to terminate the current cycle, then cut power to the unit at the breaker for 5 minutes to reboot the main control board. Keep in mind that i10 is a hard fault; it signals a physical problem. If the root cause—like a restricted hose or a failed solenoid—remains, the code will reappear the next time you attempt a wash. Always ensure the supply valve under your sink is fully open and the supply hose is free of kinks before trying again.
Common replacement parts
When to call a pro
Contact us if you have confirmed the water supply is open and the hose is clear, yet the unit still fails to fill. Diagnosing a faulty inlet valve, a clogged air trap, or a bad control board requires using a multimeter to check for continuity and live 120V voltage. A-Fix Service offers a $90 diagnostic fee (waived upon repair) and includes a 1-year warranty on all parts and labor. We stock standard Electrolux inlet valves and sensors to address i10 errors efficiently across Washington and Oregon.
FAQs
What is the typical cost to resolve an Electrolux i10 error?
If the problem is just a kinked hose or a dirty screen, there is no parts cost. If the water inlet valve requires replacement, expect a total of $150 to $250 for parts and labor. Replacing a control board may exceed $300.
Am I able to troubleshoot the i10 error myself?
Yes, you can easily inspect the under-sink shut-off valve and look for kinks in the supply line. If you are comfortable turning off the water and disconnecting the hose, you can also clean the inlet valve screen. Any electrical troubleshooting should be left to a pro.
Will the i10 code disappear on its own?
No. The i10 code will remain until the dishwasher successfully completes a fill cycle within the programmed time. Power cycling only provides a temporary reset.
How much time is required for a technician to fix this?
Replacing a water inlet valve or pressure sensor typically takes between 30 and 45 minutes once the dishwasher is accessed.
Is it harmful to run the dishwasher while the i10 code is present?
The dishwasher will not operate. The control board will lock out the cycle and trigger the drain pump to prevent flooding or damage to the wash motor.
Need help with i10?
Our certified techs diagnose Electrolux error codes daily. $90 diagnostic · 1-yr warranty.