Electrolux washer — Error Code E10
The washer is not filling with water within the allotted time.
What it means
The E10 error on Electrolux front-load or top-load machines signals that the unit has timed out during the water fill process. The main control board tracks the internal water level using a pressure sensor (transducer) or pressure switch. If the control board energizes the water inlet valve solenoids but the sensor fails to detect the required water level within the programmed window—usually 5 to 8 minutes depending on the selected cycle—the machine halts and displays E10. This safety mechanism prevents the wash heater or circulation pumps from operating without water, which would lead to burnout. This fault is classified as a fill or inlet error. It typically points to restricted household water supply, a mechanical failure within the inlet valve solenoids, or a pneumatic issue in the pressure hose assembly, such as a blockage or a pinhole leak preventing accurate hydrostatic pressure readings.
Likely Causes
- 1 Clogged Inlet Valve ScreensOver time, mineral deposits from hard water or sediment from the municipal water system can clog the fine mesh filters located inside the inlet valve connections.
- 2 Closed or Restricted Water SupplyThe hot or cold water shut-off valves behind your machine might be partially closed, or the inlet hoses could be pinched, preventing adequate flow.
- 3 Defective Water Inlet ValveThe inlet valve solenoids can fail electrically (open circuit) or become mechanically stuck in the closed position, meaning they won't let water through even when the control board sends 120V to them.
- 4 Faulty Pressure Sensor or HoseIf the pressure tube has a pinhole, has rubbed against internal components, or is clogged with lint, air pressure cannot reach the transducer, causing the board to incorrectly assume the tub is empty.
- 5 Main Control Board FailureIn less common scenarios, the triac on the main control board responsible for signaling the inlet valve solenoids may have burned out or shorted.
How to clear / reset
To clear the E10 code temporarily, press the Pause/Cancel button twice to halt the cycle and allow the machine to discharge any remaining water. Unplug the washer from the wall for 3 to 5 minutes to allow the main control board to reset. While the power is off, confirm that your home's hot and cold water valves are fully open and that the hoses are free of kinks. Restore power and attempt a new cycle. If the machine still fails to fill and the E10 code reappears, a simple reset will not suffice; you must address the specific component failure or flow restriction.
Common replacement parts
When to call a pro
Contact a professional if clearing the inlet screens and inspecting the water supply does not resolve the E10 error. Diagnosing the inlet valve solenoids requires a multimeter to check for continuity (typically around 1K ohms) and verifying that the control board is outputting 120V AC. If you are uncomfortable handling live voltage or troubleshooting pneumatic systems, it is best to call a technician. A-Fix Service provides a $90 diagnostic fee (waived if you approve the repair) and guarantees our work with a 1-year warranty on parts and labor.
FAQs
How much does it cost to fix an E10 error?
If the issue is simply clogged screens, you will only pay the $90 diagnostic/labor fee. If the water inlet valve requires replacement, total repair costs typically fall between $150 and $250, covering both parts and labor.
Can I fix the E10 code myself?
Yes, provided the problem is a closed supply valve, kinked hose, or debris in the mesh screens. You can disconnect the hoses and use a toothbrush to clean the filters. If the valve itself has failed, you will need to access the cabinet and use a multimeter for testing.
Will the E10 code clear itself?
No. The system will continue to display the error until the control board confirms a successful water fill within the set time limit.
How long does it take a pro to fix this?
A qualified technician can usually diagnose and swap out a faulty Electrolux water inlet valve or pressure switch in approximately 30 to 45 minutes.
Will running the washer with an E10 code damage it?
The machine enters a lockout state to protect itself. Attempting to bypass the error or running the washer dry can cause the inlet valve solenoids to overheat or result in damage to the wash pump.
Need help with E10?
Our certified techs diagnose Electrolux error codes daily. $90 diagnostic · 1-yr warranty.